Cell Mill of Amorphous Carbon

Most of the product production and processing in the current stage, using Cell Mill of Amorphous Carbon, using Cell Mill of Amorphous Carbon, is one of the very common ways of processing, accompanied by the continuous improvement of scientific productivity, and the technology of grading equipment It is also imminent to replace. The performance and internal configuration of the grading device of the airflow must also keep the trend of the era to continue the upgrade of the product.

In terms of airflow milling, it is important to understand its operational rules, which is very important because only familiarize the procedure, can operate correctly.
1. The operation rules of Cell Mill of Amorphous Carbon are as follows: Prepare materials after the preparation of the production order is received. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it works normally. Whether there is a phenomenon that the material is accumulated in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Cell Mill of Amorphous Carbon starts the motor to control the current and time at starting, so that the device can start running. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should not be large or small, thereby affecting the separation effect of the grinding machine, making the machine easily malfunction. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
Third, the main procedures of the closure and inspection of Cell Mill of Amorphous Carbon are as follows: After the material in the grinding machine housing is completely pulverized, the feed should be stopped, and the motor should be closed. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vessel. Fill in the corresponding production record, update the device status flag, which is convenient for the next use.



ALPA baked wheat Cell Mill of Amorphous Carbon case sharing: This customer is a seasoning company, in the production process, it is necessary to use a wheat after baked wheat. Ultrafine pulverized equipment. Investigate a number of domestic enterprises in China, and finally chose our AlPA as a partner, purchased Cell Mill of Amorphous Carbon from us.
Technical parameters:

Finished granularity: D99.9: 180 目

Production capacity: 400kg

For long-term \"health\"We need to take some steps to protect them again.
1. First, the gap of the hammer screen can be adjusted: the friction on the screen changes varies from the distance between the material and the screen, and the friction is different. Improve the hammer speed and hammer material efficiency by adjusting the hammer net gap. However, during the production process, the screens they use are different, the raw materials are different, the hammer screening gap needs to be adjusted; in the crusher, the crusher is not very good at the beginning, but after a period of time Work, the particles inside the crusher also changes; in the grinding machine parts, the hammer head is easily worn, and the gap between the hammer head and the screen is increased, and the yield is also declining, it is difficult to maintain.

Of course, in order to test the yield of a crusher, for some of the raw materials, for some screen holes, in order to determine the appropriate hammer sieve gap and suction, the useful life of the screen and the hammer can be obtained in a short time. Very high grinding efficiency data. However, in the production of feed grinding, such specific measurement data, according to the operator's work experience, the technical content of the crusher itself is two things. People with enrichment of experience and labor experience also require higher operating costs. When the hammer is worn, the gap between the hammer and the sieve increases, the friction is reduced, and the abrasive efficiency is lowered.

2. Cell Mill of Amorphous Carbon mainly requires a reasonable use of reverse glitch: mainly to rush the side hair of the screen into the inside, greatly increase the friction, but this method is not used for a long time. After the globi polishing, the efficiency is lowered. It lasts for 30 minutes to 1 hour.
3. Put the friction piece into the Cell Mill of Amorphous Carbon: The friction plate has the effect of the material ring, but the effect is limited. First, the teeth of the friction plate are in front of the hammer head, the friction surface is small, and the hammer is long-lasting; if the sieve area is too small, the output screen area will be reduced.
For any of the equipment, everyday maintenance can be performed, to ensure that the equipment can operate for a long time, so daily is critical to Cell Mill of Amorphous Carbon.


ALPA designated Cell Mill of Amorphous Carbon equipment has gained a very good reputation in actual production applications, and it has also won the praise of users and friends. If you need to purchase Cell Mill of Amorphous Carbon, please feel free to contact us.