good balance of performance Ring Roller Mill machine for uranium, just need to place it can be produced on a stable ground, and low noise, dust leakage problems can be avoided in the process of crushing, powder favored by the industry.
In terms of airflow milling, it is important to understand its operational rules, which is very important because only familiarize the procedure, can operate correctly.
a, Ring Roller Mill machine for uranium operation rules are as follows: After preparing the production order is received before the start, to prepare materials. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it works normally. Whether there is a phenomenon that the material is accumulated in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
bis, Ring Roller mill machine for uranium starter motor to start first, and the control current start time, enabled device starts to operate. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should not be large or small, thereby affecting the separation effect of the grinding machine, making the machine easily malfunction. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
III, Ring Roller mill machine for uranium and closing the main inspection procedures as follows: Grinding Machine housing material is completely pulverized after separation, should stop feeding off the motor. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vessel. Fill in the corresponding production record, update the device status flag, which is convenient for the next use.
ALPA battery material powder Ring Roller mill machine for uranium Case Studies:
an industrial company main business areas: new energy storage materials, electronic ceramic materials technology and industry, secondary resource reproduction and new technology industry, biological engineering polymer materials, technology development and network products, electronic products, technology transfer, training and technology; manufacturing, product development and after sales related materials and equipment; international technical cooperation and trade-related areas technical training; required to run enterprise products and technology export business and the business of machinery and equipment, spare parts, raw and auxiliary materials import and export business of technology.
Case Parameters:
Product size: D50: 5.8UM
Hour Yield: 800kg
Let's talk about how to use Ring Roller Mill Machine for Uranium method
1. Prepare the host, attachment machine, pipeline and Whether the valve is intact, whether it works fine.
Second, open
1. Turn on the compressor power supply, the pressure valve and the main valve of the dust collector, then turn on the power switch of the powder machine, and turn on the power.
2. From the zero start grading wheel and gradually adjust to the specified speed.
3. Several turning wind turbines, cyclone separators discharge, dust removal, feed motor power, and then turn on the total power supply of the tube bar, set the inverter frequency, and then begins to break.
4. The particle size of the finished wheel can be adjusted by grading wheel frequencies and charging.
Third, the order of shutdown is: inverter - feeder - Main valve - Compressor - Stepper wheel Motor - Cyclone discharge, dust removal switch - Fan - Total Power - Air Compressor.
4, repair
1. The motor should be lubed regularly, but the grease should not be too large, the bearing temperature is too high.
2. Hierarchical impeller, spiral feeder, crushing nozzle wear should pay attention to check, belt tight and suitable.
3. After a crushing material, after a certain period of time, it is necessary to remove the viscosity of the chalk, so as not to block, thereby affecting the crushing effect.
4. After the filter bag, you should clean or replace it.
V. Note
1. When the discharge device is running, the unloading port cannot be extended to avoid accidents.
2. The rotational speed of the impeller must not exceed the specified requirements, otherwise the temperature is too high, the impeller, and the electric machine are damaged.
3. Regularly check the safety valve to ensure safety.
The above is the Ring Roller Mill Machine for Uranium, which is introduced. You can make a brief understanding, you need to purchase eddy current pulverizer, disc air crusher, users of ultrafine crusher, please contact us [123 ]
