Most of the product production and processing in the current phase use Turbo Pulverizer of Rubber Chemicals, using Turbo Pulverizer of Rubber Chemicals, is a very common way of processing, accompanied by the continuous improvement of scientific productivity, grading equipment technology It is also imminent to replace. The performance and internal configuration of the grading device of the airflow must also keep the trend of the era to continue the upgrade of the product.
Which factors affect the performance parameters used by Turbo Pulverizer of Rubber Chemicals?
The following is a detailed description:
1. Feeding particle size control
Most Turbo Pulverizer of Rubber Chemicals has a certain upper limit requirement for feed particle size. After entering the pulverization cavity, it can be sufficiently accelerated before collision and crushing with other particles. It is difficult to completely accelerate after large particles enter the pulverized cavity, which will allow them to stay in the machine too long, resulting in too high energy consumption. Therefore, in large-scale production of ultrafine powder, it is an effective way to pre-ground the raw material of the particle size is an effective pathway for energy saving.
2. Working medium
Currently, Turbo Pulverizer of Rubber Chemicals work media is mainly compressed, superheated steam, inert gas, and the like. The choice of working fluid has a certain impact on crushing effects and economics. Superheated steam is superior to air in fluidity and critical flow rates to achieve higher flow rates and uniform flow fields. However, using superheated steam as a working fluid, it must be ensured that it is still in an overheating state before entering the product capture device, otherwise the material is condensed.
3. Feeding speed
Feeding speed is an important parameter reflecting gas flow grinding production capacity. During the pulverization process, the optimum ratio of the intake flow rate and the feed speed is the key to improving the crushing efficiency. In general, under certain intake flow conditions, the feed speed is proportional to the particle size of the product. However, the feeding speed is too fast, which will increase the particle density, mutual interference, disadvantage of the particles, and difficult to achieve the sufficient and effective collision between particles, affect the crushing effect; although the feed speed is too slow, the particles stay in the crush area The time can be extended, which will reduce the particle density, reduce the collision rate, resulting in a decrease in production capacity and an increase in unit production energy consumption.
4. Granular limit
Turbo pulverizer of rubber chemicals In the pulverization process, as the material particle size decreases, the crystallization uniformity and intensity of the material increases. After reaching a certain degree, the particle size of the material is no longer reduced or reduced.That is, the material's crushing limit is reached. At this time, the material specific surface area increases, the surface activity of the particles, the particle agglomeration and grinding are in a dynamic equilibrium state, even if the grinding time is prolonged, it is difficult to further reduce the particle size of the material.
ALPA Battery Turbo Pulverizer of Rubber Chemicals Case Sharing:
A energy company is a battery-based material production enterprise with multiple production bases. The company's business scope includes new materials and main products research and development, battery materials and their accessories research, etc. The top of the list.
Case parameters:
Product particle size: D50: 15μm
Ultra-micro Pulverizer of Rubber ChemicalS correct usage:
1, ultra-microfinator and The power unit should be installed firmly. If the ultrafine pulverizer is fixed, it should be fixed on the cement; if the pulverizer is a mobile operation, the unit should be installed on the base made of angle iron, and ensure the power machine (diesel or electric motor) and the pulverizer The belt wheel groove is in the same turning plane.
2, after the pulverizer is installed, check the fastening of the fasteners of each part, if there is loose to tighten. At the same time, check if the leather belt looseness is appropriate.
3 Whether the power machine and the pulverizing machine are lubricated.
5
6. At any time, you should pay attention to the operation of the pulverizer, and the feed should be evenly charged to prevent blocking, do not have a long time overload. If there is found that vibration, noise, the bearing and the body temperature is too high, the outer spray, etc., should be closed immediately, and the fault can be eliminated.
ALPA production of Turbo Pulverizer of Rubber Chemicals is equipped with high quality equipment, which supports customization, equipment models, high efficiency, low energy consumption, easy operation, 24 hours, please consult!
